Lian Li LanCool K58 (PC-K58-B) Advance Mid
Tower Computer PC Case- BLACK, Supports CrossfireX and 3-Way SLI
The Dragon Lord K series builds LanCools high
standard of Quality requirement. This SECC steel cases with completely tool-less
design are the perfect complement to a PC gamers' needs. The look of Dragon
Lord K58 has no door panel design; users can access the external drive easier.
The two red stripes on the front panel done in attractive anodized aluminum give
a flamboyant finishing touch to this outstanding high-end chassis.
Features:
The Dragon Lord K58 is targeted for the LAN
party gamers. It is a mid-tower case, which is ideal for the latest graphics
cards in combination with the best thermal dynamics. All the internal
installation can be done without tools, and is easily adjustable to optimize
your hardware setup. Especially in the advent of adding in new graphics
cards, equipped with 8 PCI slots, can hold three or more graphics cards,
supports CrossfireX and 3-way SLI.
The new internal layout has the motherboard
on top of the power supply unit, which allows for easier access to the
motherboard as well as more room above, thus larger CPU coolers can be used.
The power supply unit at the button of the case is cooled with fresh cool
air directly from the outside of the case, instead of pre-heated air from
within. This will bring down the core temperatures and extend the lifespan
of the PSU significantly
To install motherboard require no tools,
use tool-less screw to screw a motherboard on case, easily and quickly.
Silent Performance:
The Dragon Lord K58 is equipped with large
cooling fans, with low RPM, which still provide enough air flow to cool down
the hardware adequately. The front 140mm intakes fan runs at 1000RPM. The
top two silent 140mm ball-bearing fans exhaust the hot air out at 1000RPM
The fans on the top panel are mounted with
Lian Lis new anti-vibration fan mounting system; the rubber ring grommet
absorbs the vibration, keeping the case silent.
The new 5.25 bay tool-less mounting
incorporates a mounting bar equipped with rubber padding. After secure the
mounting bar, the rubber pad pushes and holds the 5.25 device in position
to secure and absorb vibration from the device.
The too-less HDD cage combines with
patented anti-vibration rubber grommets to suspend the HDDs in a noise free
environment. The two buckles on both side to hold the HDD in position, also
absorb and reduce vibrations.
The aluminum PCI tool-less mounting module
is equipped with a rubber pad which can hold the graphics card firmly while
closing the gap found in the PCI bracket and PCI slot to reduce noise from
escaping air and furthermore reduce vibrations.
The Power Supply has rubber pads for both
insulation and support. The mounting clip is also aligned with rubber to
reduce vibrations but also and also secure the PSU without scratching the
painted surface.
There are special air intake vents at the
front of the case, allow cold air to enter , also keep system noise inside
the case.
Creative Thermal Solutions:
Dragon Lord K58 inputs cold air by the
140mm (1000RPM) intake fan, There are also vents on the 5.25 bezels, allow
cold air to enter the case to cool the system down
There are vents on the PCI slots, provides
extra cooling to graphics card.
The power supply unit is at the bottom of
the case. It can draw in cold air directly through the vent below the power
supply unit. This cooler, fresh air will keep your PSU components more cool
and stable and thus extend the PSU lifecycle.
Dragon Lord K58 supports liquid cooling
system, the two holes at the rear of the case allows water tubes to pass
through, and the rubber cover can protect the tubes away from cutting.
The Dragon Load k58 feature a high density
vent design, to make sure fans remove the system hot air out of the case
totally.
User Friendly:
2009 has seen an all-new tool-less design
from Dragon Lord K series chassis. To do this required a great many
innovative patents to be filed worldwide. The ideas will make installing and
maintenance much easier. For example when installing the 5.25 optical
drive, just slide the drive into the 5.25 bay, and close the mounting bar
to secure the optical drive, as simple as that.
The installation of the hard disk is very
easy, and tool-less. Place the hard disk into the aluminum cage, and fasten
the bucks to secure the hard disk.(2.5 HDD install feasible), Slide the hard
disk within the cage into the special hard disk rack with the rubber
suspension grommet.
To install PCI add-on cards require no
tools at all. Simply open the aluminum arm of the tool-less PCI add-on card
holder, insert the add-on card to the motherboard slots, and close the
aluminum arm to hold the add-on card in position. The additional rubber
padding on the aluminum arm assists in gripping the card bracket and
securing it firmly.
To install PSU require no tools. Simply
open the aluminum PSU holder, insert the PSU in position, also can turn
PSU's fans up or down to suit your need, then close the aluminum PSU holder.
There is an air filter at the base of the
case to stop dust from entering the case. The filter is washable. The vents
are specially designed to retard heat and fire crossover should a short
circuit cause sparks and excessive heat within your system. This feature is
designed to prevent the problem from spreading outside your case should the
unlikely event occur with your components.
The intake fans are aligned with inlet
holes on the bezels. These are equipped with air filters to stop the dust
and keep the internals dust free and clean.
Specifications:
Model
PC-K58
Case Type
Advance
Mid Tower
Dimensions
214mm x
496mm x 498 mm (W, H, D)
Front bezel Material
Plastic
Color
Black
Side Panel
SECC
Steel
Body Material
SECC
Steel
Net Weight
5.25 drive bay (External)
5
3.5 drive bay (External)
3.5 drive bay (Internal)
4
Expansion Slot
8
Motherboard
ATX / M-ATX
System Fan (Front)
140mm Fan
x 1 (1000RPM)
System Fan (Top)
K58 top
cover fans require special mounting kit ( OF-01) (Optional)
Lian Li LanCool K58 (PC-K58-B) Advance Mid
Tower Computer PC Case- BLACK, Supports CrossfireX and 3-Way SLI
The Dragon Lord K series builds LanCools high
standard of Quality requirement. This SECC steel cases with completely tool-less
design are the perfect complement to a PC gamers' needs. The look of Dragon
Lord K58 has no door panel design; users can access the external drive easier.
The two red stripes on the front panel done in attractive anodized aluminum give
a flamboyant finishing touch to this outstanding high-end chassis.
Features:
The Dragon Lord K58 is targeted for the LAN
party gamers. It is a mid-tower case, which is ideal for the latest graphics
cards in combination with the best thermal dynamics. All the internal
installation can be done without tools, and is easily adjustable to optimize
your hardware setup. Especially in the advent of adding in new graphics
cards, equipped with 8 PCI slots, can hold three or more graphics cards,
supports CrossfireX and 3-way SLI.
The new internal layout has the motherboard
on top of the power supply unit, which allows for easier access to the
motherboard as well as more room above, thus larger CPU coolers can be used.
The power supply unit at the button of the case is cooled with fresh cool
air directly from the outside of the case, instead of pre-heated air from
within. This will bring down the core temperatures and extend the lifespan
of the PSU significantly
To install motherboard require no tools,
use tool-less screw to screw a motherboard on case, easily and quickly.
Silent Performance:
The Dragon Lord K58 is equipped with large
cooling fans, with low RPM, which still provide enough air flow to cool down
the hardware adequately. The front 140mm intakes fan runs at 1000RPM. The
top two silent 140mm ball-bearing fans exhaust the hot air out at 1000RPM
The fans on the top panel are mounted with
Lian Lis new anti-vibration fan mounting system; the rubber ring grommet
absorbs the vibration, keeping the case silent.
The new 5.25 bay tool-less mounting
incorporates a mounting bar equipped with rubber padding. After secure the
mounting bar, the rubber pad pushes and holds the 5.25 device in position
to secure and absorb vibration from the device.
The too-less HDD cage combines with
patented anti-vibration rubber grommets to suspend the HDDs in a noise free
environment. The two buckles on both side to hold the HDD in position, also
absorb and reduce vibrations.
The aluminum PCI tool-less mounting module
is equipped with a rubber pad which can hold the graphics card firmly while
closing the gap found in the PCI bracket and PCI slot to reduce noise from
escaping air and furthermore reduce vibrations.
The Power Supply has rubber pads for both
insulation and support. The mounting clip is also aligned with rubber to
reduce vibrations but also and also secure the PSU without scratching the
painted surface.
There are special air intake vents at the
front of the case, allow cold air to enter , also keep system noise inside
the case.
Creative Thermal Solutions:
Dragon Lord K58 inputs cold air by the
140mm (1000RPM) intake fan, There are also vents on the 5.25 bezels, allow
cold air to enter the case to cool the system down
There are vents on the PCI slots, provides
extra cooling to graphics card.
The power supply unit is at the bottom of
the case. It can draw in cold air directly through the vent below the power
supply unit. This cooler, fresh air will keep your PSU components more cool
and stable and thus extend the PSU lifecycle.
Dragon Lord K58 supports liquid cooling
system, the two holes at the rear of the case allows water tubes to pass
through, and the rubber cover can protect the tubes away from cutting.
The Dragon Load k58 feature a high density
vent design, to make sure fans remove the system hot air out of the case
totally.
User Friendly:
2009 has seen an all-new tool-less design
from Dragon Lord K series chassis. To do this required a great many
innovative patents to be filed worldwide. The ideas will make installing and
maintenance much easier. For example when installing the 5.25 optical
drive, just slide the drive into the 5.25 bay, and close the mounting bar
to secure the optical drive, as simple as that.
The installation of the hard disk is very
easy, and tool-less. Place the hard disk into the aluminum cage, and fasten
the bucks to secure the hard disk.(2.5 HDD install feasible), Slide the hard
disk within the cage into the special hard disk rack with the rubber
suspension grommet.
To install PCI add-on cards require no
tools at all. Simply open the aluminum arm of the tool-less PCI add-on card
holder, insert the add-on card to the motherboard slots, and close the
aluminum arm to hold the add-on card in position. The additional rubber
padding on the aluminum arm assists in gripping the card bracket and
securing it firmly.
To install PSU require no tools. Simply
open the aluminum PSU holder, insert the PSU in position, also can turn
PSU's fans up or down to suit your need, then close the aluminum PSU holder.
There is an air filter at the base of the
case to stop dust from entering the case. The filter is washable. The vents
are specially designed to retard heat and fire crossover should a short
circuit cause sparks and excessive heat within your system. This feature is
designed to prevent the problem from spreading outside your case should the
unlikely event occur with your components.
The intake fans are aligned with inlet
holes on the bezels. These are equipped with air filters to stop the dust
and keep the internals dust free and clean.
Specifications:
Model
PC-K58
Case Type
Advance
Mid Tower
Dimensions
214mm x
496mm x 498 mm (W, H, D)
Front bezel Material
Plastic
Color
Black
Side Panel
SECC
Steel
Body Material
SECC
Steel
Net Weight
5.25 drive bay (External)
5
3.5 drive bay (External)
3.5 drive bay (Internal)
4
Expansion Slot
8
Motherboard
ATX / M-ATX
System Fan (Front)
140mm Fan
x 1 (1000RPM)
System Fan (Top)
K58 top
cover fans require special mounting kit ( OF-01) (Optional)
Configure Lian Li Lancool Dragon Lord PC-K58 Aluminum/ SECC ATX Mid Tower Computer Case
OR
product
https://www.performance-pcs.com/lian-li-lancool-dragon-lord-pc-k58-aluminum-secc-atx-mid-tower-computer-case-pc-k58.html5396Lian Li Lancool Dragon Lord PC-K58 Aluminum/ SECC ATX Mid Tower Computer Casehttps://www.performance-pcs.com/media/catalog/product/t/m/tmpk58_main_01.jpg99.9999.9900USDInStock/Chassis/Midtower Chassis<h3><font face="Tahoma">Product Details:</font></h3><p><font size="2" face="Tahoma"><b>Lian Li LanCool K58 (PC-K58-B) Advance Mid
Tower Computer PC Case- BLACK, Supports CrossfireX and 3-Way SLI</b></font></p>
<p><font size="2" face="Tahoma">The Dragon Lord K series builds LanCools high
standard of Quality requirement. This SECC steel cases with completely tool-less
design are the perfect complement to a PC gamers' needs. The look of Dragon
Lord K58 has no door panel design; users can access the external drive easier.
The two red stripes on the front panel done in attractive anodized aluminum give
a flamboyant finishing touch to this outstanding high-end chassis.</font></p>
<p><b><font size="2" face="Tahoma">Features:</font></b></p>
<ul><li><font size="2" face="Tahoma">The Dragon Lord K58 is targeted for the LAN
party gamers. It is a mid-tower case, which is ideal for the latest graphics
cards in combination with the best thermal dynamics. All the internal
installation can be done without tools, and is easily adjustable to optimize
your hardware setup. Especially in the advent of adding in new graphics
cards, equipped with 8 PCI slots, can hold three or more graphics cards,
supports CrossfireX and 3-way SLI.</font></li><li><font size="2" face="Tahoma">The new internal layout has the motherboard
on top of the power supply unit, which allows for easier access to the
motherboard as well as more room above, thus larger CPU coolers can be used.
The power supply unit at the button of the case is cooled with fresh cool
air directly from the outside of the case, instead of pre-heated air from
within. This will bring down the core temperatures and extend the lifespan
of the PSU significantly</font></li><li><font size="2" face="Tahoma">To install motherboard require no tools,
use tool-less screw to screw a motherboard on case, easily and quickly.</font></li></ul>
<p><b><font size="2" face="Tahoma">Silent Performance:</font></b></p>
<ul><li><font size="2" face="Tahoma">The Dragon Lord K58 is equipped with large
cooling fans, with low RPM, which still provide enough air flow to cool down
the hardware adequately. The front 140mm intakes fan runs at 1000RPM. The
top two silent 140mm ball-bearing fans exhaust the hot air out at 1000RPM</font></li><li><font size="2" face="Tahoma">The fans on the top panel are mounted with
Lian Lis new anti-vibration fan mounting system; the rubber ring grommet
absorbs the vibration, keeping the case silent.</font></li><li><font size="2" face="Tahoma">The new 5.25 bay tool-less mounting
incorporates a mounting bar equipped with rubber padding. After secure the
mounting bar, the rubber pad pushes and holds the 5.25 device in position
to secure and absorb vibration from the device.</font></li><li><font size="2" face="Tahoma">The too-less HDD cage combines with
patented anti-vibration rubber grommets to suspend the HDDs in a noise free
environment. The two buckles on both side to hold the HDD in position, also
absorb and reduce vibrations.</font></li><li><font size="2" face="Tahoma">The aluminum PCI tool-less mounting module
is equipped with a rubber pad which can hold the graphics card firmly while
closing the gap found in the PCI bracket and PCI slot to reduce noise from
escaping air and furthermore reduce vibrations.</font></li><li><font size="2" face="Tahoma">The Power Supply has rubber pads for both
insulation and support. The mounting clip is also aligned with rubber to
reduce vibrations but also and also secure the PSU without scratching the
painted surface.</font></li><li><font size="2" face="Tahoma">There are special air intake vents at the
front of the case, allow cold air to enter , also keep system noise inside
the case.</font></li></ul>
<p><b><font size="2" face="Tahoma">Creative Thermal Solutions:</font></b></p>
<ul><li><font size="2" face="Tahoma">Dragon Lord K58 inputs cold air by the
140mm (1000RPM) intake fan, There are also vents on the 5.25 bezels, allow
cold air to enter the case to cool the system down</font></li><li><font size="2" face="Tahoma">There are vents on the PCI slots, provides
extra cooling to graphics card.</font></li><li><font size="2" face="Tahoma">The power supply unit is at the bottom of
the case. It can draw in cold air directly through the vent below the power
supply unit. This cooler, fresh air will keep your PSU components more cool
and stable and thus extend the PSU lifecycle.</font></li><li><font size="2" face="Tahoma">Dragon Lord K58 supports liquid cooling
system, the two holes at the rear of the case allows water tubes to pass
through, and the rubber cover can protect the tubes away from cutting.</font></li><li><font size="2" face="Tahoma">The Dragon Load k58 feature a high density
vent design, to make sure fans remove the system hot air out of the case
totally.</font></li></ul>
<p><b><font size="2" face="Tahoma">User Friendly:</font></b></p>
<ul><li><font size="2" face="Tahoma">2009 has seen an all-new tool-less design
from Dragon Lord K series chassis. To do this required a great many
innovative patents to be filed worldwide. The ideas will make installing and
maintenance much easier. For example when installing the 5.25 optical
drive, just slide the drive into the 5.25 bay, and close the mounting bar
to secure the optical drive, as simple as that.</font></li><li><font size="2" face="Tahoma">The installation of the hard disk is very
easy, and tool-less. Place the hard disk into the aluminum cage, and fasten
the bucks to secure the hard disk.(2.5 HDD install feasible), Slide the hard
disk within the cage into the special hard disk rack with the rubber
suspension grommet.</font></li><li><font size="2" face="Tahoma">To install PCI add-on cards require no
tools at all. Simply open the aluminum arm of the tool-less PCI add-on card
holder, insert the add-on card to the motherboard slots, and close the
aluminum arm to hold the add-on card in position. The additional rubber
padding on the aluminum arm assists in gripping the card bracket and
securing it firmly.</font></li><li><font size="2" face="Tahoma">To install PSU require no tools. Simply
open the aluminum PSU holder, insert the PSU in position, also can turn
PSU's fans up or down to suit your need, then close the aluminum PSU holder.</font></li><li><font size="2" face="Tahoma">There is an air filter at the base of the
case to stop dust from entering the case. The filter is washable. The vents
are specially designed to retard heat and fire crossover should a short
circuit cause sparks and excessive heat within your system. This feature is
designed to prevent the problem from spreading outside your case should the
unlikely event occur with your components.</font></li><li><font size="2" face="Tahoma">The intake fans are aligned with inlet
holes on the bezels. These are equipped with air filters to stop the dust
and keep the internals dust free and clean.</font></li></ul>
<p><font size="2" face="Tahoma"><b>Specifications:</b> </font></p>
<font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><table width="614" cellspacing="0" cellpadding="3" border="1" bgcolor="#ffffff">
<tbody><tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Model</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">PC-K58 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Case Type</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">Advance
Mid Tower </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Dimensions </font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">214mm x
496mm x 498 mm (W, H, D) </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Front bezel Material</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">Plastic </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Color</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">Black </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Side Panel</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">SECC
Steel </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Body Material</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">SECC
Steel </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Net Weight </font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma"> </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
5.25 drive bay (External)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">5 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
3.5 drive bay (External)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma"> </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
3.5 drive bay (Internal)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">4 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Expansion Slot</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">8 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Motherboard</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">ATX / M-ATX </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
System Fan (Front)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">140mm Fan
x 1 (1000RPM) </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
System Fan (Top)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">K58 top
cover fans require special mounting kit ( OF-01)<b> (Optional) </b></font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
System Fan (Rear)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">120mm Fan
x 1 (1500RPM) </font></td>
</tr>
</tbody></table> <h3><font face="Tahoma">Product Details:</font></h3><p><font size="2" face="Tahoma"><b>Lian Li LanCool K58 (PC-K58-B) Advance Mid
Tower Computer PC Case- BLACK, Supports CrossfireX and 3-Way SLI</b></font></p>
<p><font size="2" face="Tahoma">The Dragon Lord K series builds LanCools high
standard of Quality requirement. This SECC steel cases with completely tool-less
design are the perfect complement to a PC gamers' needs. The look of Dragon
Lord K58 has no door panel design; users can access the external drive easier.
The two red stripes on the front panel done in attractive anodized aluminum give
a flamboyant finishing touch to this outstanding high-end chassis.</font></p>
<p><b><font size="2" face="Tahoma">Features:</font></b></p>
<ul><li><font size="2" face="Tahoma">The Dragon Lord K58 is targeted for the LAN
party gamers. It is a mid-tower case, which is ideal for the latest graphics
cards in combination with the best thermal dynamics. All the internal
installation can be done without tools, and is easily adjustable to optimize
your hardware setup. Especially in the advent of adding in new graphics
cards, equipped with 8 PCI slots, can hold three or more graphics cards,
supports CrossfireX and 3-way SLI.</font></li><li><font size="2" face="Tahoma">The new internal layout has the motherboard
on top of the power supply unit, which allows for easier access to the
motherboard as well as more room above, thus larger CPU coolers can be used.
The power supply unit at the button of the case is cooled with fresh cool
air directly from the outside of the case, instead of pre-heated air from
within. This will bring down the core temperatures and extend the lifespan
of the PSU significantly</font></li><li><font size="2" face="Tahoma">To install motherboard require no tools,
use tool-less screw to screw a motherboard on case, easily and quickly.</font></li></ul>
<p><b><font size="2" face="Tahoma">Silent Performance:</font></b></p>
<ul><li><font size="2" face="Tahoma">The Dragon Lord K58 is equipped with large
cooling fans, with low RPM, which still provide enough air flow to cool down
the hardware adequately. The front 140mm intakes fan runs at 1000RPM. The
top two silent 140mm ball-bearing fans exhaust the hot air out at 1000RPM</font></li><li><font size="2" face="Tahoma">The fans on the top panel are mounted with
Lian Lis new anti-vibration fan mounting system; the rubber ring grommet
absorbs the vibration, keeping the case silent.</font></li><li><font size="2" face="Tahoma">The new 5.25 bay tool-less mounting
incorporates a mounting bar equipped with rubber padding. After secure the
mounting bar, the rubber pad pushes and holds the 5.25 device in position
to secure and absorb vibration from the device.</font></li><li><font size="2" face="Tahoma">The too-less HDD cage combines with
patented anti-vibration rubber grommets to suspend the HDDs in a noise free
environment. The two buckles on both side to hold the HDD in position, also
absorb and reduce vibrations.</font></li><li><font size="2" face="Tahoma">The aluminum PCI tool-less mounting module
is equipped with a rubber pad which can hold the graphics card firmly while
closing the gap found in the PCI bracket and PCI slot to reduce noise from
escaping air and furthermore reduce vibrations.</font></li><li><font size="2" face="Tahoma">The Power Supply has rubber pads for both
insulation and support. The mounting clip is also aligned with rubber to
reduce vibrations but also and also secure the PSU without scratching the
painted surface.</font></li><li><font size="2" face="Tahoma">There are special air intake vents at the
front of the case, allow cold air to enter , also keep system noise inside
the case.</font></li></ul>
<p><b><font size="2" face="Tahoma">Creative Thermal Solutions:</font></b></p>
<ul><li><font size="2" face="Tahoma">Dragon Lord K58 inputs cold air by the
140mm (1000RPM) intake fan, There are also vents on the 5.25 bezels, allow
cold air to enter the case to cool the system down</font></li><li><font size="2" face="Tahoma">There are vents on the PCI slots, provides
extra cooling to graphics card.</font></li><li><font size="2" face="Tahoma">The power supply unit is at the bottom of
the case. It can draw in cold air directly through the vent below the power
supply unit. This cooler, fresh air will keep your PSU components more cool
and stable and thus extend the PSU lifecycle.</font></li><li><font size="2" face="Tahoma">Dragon Lord K58 supports liquid cooling
system, the two holes at the rear of the case allows water tubes to pass
through, and the rubber cover can protect the tubes away from cutting.</font></li><li><font size="2" face="Tahoma">The Dragon Load k58 feature a high density
vent design, to make sure fans remove the system hot air out of the case
totally.</font></li></ul>
<p><b><font size="2" face="Tahoma">User Friendly:</font></b></p>
<ul><li><font size="2" face="Tahoma">2009 has seen an all-new tool-less design
from Dragon Lord K series chassis. To do this required a great many
innovative patents to be filed worldwide. The ideas will make installing and
maintenance much easier. For example when installing the 5.25 optical
drive, just slide the drive into the 5.25 bay, and close the mounting bar
to secure the optical drive, as simple as that.</font></li><li><font size="2" face="Tahoma">The installation of the hard disk is very
easy, and tool-less. Place the hard disk into the aluminum cage, and fasten
the bucks to secure the hard disk.(2.5 HDD install feasible), Slide the hard
disk within the cage into the special hard disk rack with the rubber
suspension grommet.</font></li><li><font size="2" face="Tahoma">To install PCI add-on cards require no
tools at all. Simply open the aluminum arm of the tool-less PCI add-on card
holder, insert the add-on card to the motherboard slots, and close the
aluminum arm to hold the add-on card in position. The additional rubber
padding on the aluminum arm assists in gripping the card bracket and
securing it firmly.</font></li><li><font size="2" face="Tahoma">To install PSU require no tools. Simply
open the aluminum PSU holder, insert the PSU in position, also can turn
PSU's fans up or down to suit your need, then close the aluminum PSU holder.</font></li><li><font size="2" face="Tahoma">There is an air filter at the base of the
case to stop dust from entering the case. The filter is washable. The vents
are specially designed to retard heat and fire crossover should a short
circuit cause sparks and excessive heat within your system. This feature is
designed to prevent the problem from spreading outside your case should the
unlikely event occur with your components.</font></li><li><font size="2" face="Tahoma">The intake fans are aligned with inlet
holes on the bezels. These are equipped with air filters to stop the dust
and keep the internals dust free and clean.</font></li></ul>
<p><font size="2" face="Tahoma"><b>Specifications:</b> </font></p>
<font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><font size="2" face="Arial" color="#676767"> </font><table width="614" cellspacing="0" cellpadding="3" border="1" bgcolor="#ffffff">
<tbody><tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Model</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">PC-K58 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Case Type</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">Advance
Mid Tower </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Dimensions </font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">214mm x
496mm x 498 mm (W, H, D) </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Front bezel Material</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">Plastic </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Color</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">Black </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Side Panel</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">SECC
Steel </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Body Material</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">SECC
Steel </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Net Weight </font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma"> </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
5.25 drive bay (External)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">5 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
3.5 drive bay (External)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma"> </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
3.5 drive bay (Internal)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">4 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Expansion Slot</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">8 </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
Motherboard</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">ATX / M-ATX </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
System Fan (Front)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">140mm Fan
x 1 (1000RPM) </font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
System Fan (Top)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">K58 top
cover fans require special mounting kit ( OF-01)<b> (Optional) </b></font></td>
</tr>
<tr height="27">
<td width="183" bgcolor="#ffffff"><strong><font size="2" face="Tahoma">
System Fan (Rear)</font></strong></td>
<td width="416" bgcolor="#ffffff"><font size="2" face="Tahoma">120mm Fan
x 1 (1500RPM) </font></td>
</tr>
</tbody></table>Lian-Li00https://www.performance-pcs.com/media/catalog/product/t/m/tmpk58_main_02.jpghttps://www.performance-pcs.com/media/catalog/product/t/m/tmpk58_main_03.jpghttps://www.performance-pcs.com/media/catalog/product/t/m/tmpk58_main_04.jpghttps://www.performance-pcs.com/media/catalog/product/t/m/tmpk58_main_05.jpghttps://www.performance-pcs.com/media/catalog/product/t/m/tmpk58_main_06.jpg69.9900Lian-Li