Coolsleeves™ are extruded PVC coils designed to be wrapped around soft vinyl and thin wall tubes, to eliminate tube kinking and flattening in medium to sharp bend areas.
Coolsleeves™ are extruded PVC coils designed to be wrapped around soft vinyl and thin wall tubes, to eliminate tube kinking and flattening in medium to sharp bend areas.
Coolsleeves™ are available in two different sizes:
Coolsleeves™ 500 for 1/2" OD tubing
Coolsleeves™ 625 for 5/8" OD tubing
Each size is available in 4 different colors: clear transparent (non UV reactive), Horizon blue (UV reactive), Saturn Green (UV reactive), and Red (non UV reactive)
Coolsleeves™ are shipped in precut 40" length. One length is typically sufficient for a single CPU cooling circuit depending on how tight the coils are wrapped around the tubing. Two lengths are necessary for a complete circuit including dual CPU, CPU+VGA, or CPU+VGA+Chipset setups.
The advantages of Coolsleeves™ coils are multiple:
1. Performance:
Coolsleeves™ coils do not restrict flow rate compared to internal springs
2. Reliability:
Coolsleeves™ coils completely eliminate flattening of the tubes over time
Coolsleeves™ UV reactive coils are a safe alternative to UV reactive coolant dies and prevent the pump failures caused by these dies.
Coolsleeves™ coils allow to bend soft vinyl and Tygon tubing at sharp radii without kinking. The sharpest possible radius is achieved by spacing the coils close to each other (3/16"):
Minimum bending radius for 1/2" Coolsleeves is 1.25"
Minimum bending radius for 5/8" Coolsleeves is 2.5"
A 1.25" bending radius is achieved here with Coolsleeves™ 500
A 2.5" bending radius is achieved here with Coolsleeves™ 625 and 5/8" Tygon tubing, with a fairly large spacing of 1/4" between coils.
A 2.5" bending radius is achieved here with Coolsleeves™ 625, and inexpensive 5/8" "thin wall" vinyl tubing, with the coils spaced fairly close to each other (3/16"). Wider coil spacing would not prevent kinking with this type of tubing.
4. Convenience:
Coolsleeves™ can be used with existing 1/2" OD tubing systems to reshape tubes that have flattened over time without disassembling the system.
Coolsleeves™ 625 now allow users of 1/2" ID tubing to use "thin wall" 5/8" tubes instead of 3/4", for a significant reduction in clutter inside the chassis, and radii that were absolutely impossible to achieve with 3/4" tubing.
5. Cosmetics:
Coolsleeves™ UV reactive coils are fun and attractive under UV light:
..Or in normal light:
6. Cost to consumers:
Coolsleeves™ 500 coils are more economical than other solutions: the cost per foot including vinyl tubing is up to 50% less than Clearflex™, and up to one third the cost of Tygon™ tubing.
https://www.performance-pcs.com/swiftech-500-coolsleeves-uv-green-cs500-green-d.html2792Swiftech 500 Coolsleeves - UV Greenhttps://www.performance-pcs.com/media/catalog/product/c/s/cs500-green-d_01_1.jpg3.953.9500USDInStock/Water Cooling/Water Tubing (Soft & Hard)/Tubing Springs & Sleeves<p>Coolsleeves™ are extruded PVC coils designed to be wrapped around soft vinyl and thin wall tubes, to eliminate tube kinking and flattening in medium to sharp bend areas.</p> <p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">Coolsleeves™ are extruded PVC coils designed to be wrapped around soft vinyl and thin wall tubes, to eliminate tube kinking and flattening in medium to sharp bend areas.<br /></span></p>
<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">Coolsleeves™ are available in two different sizes:</span></p>
<ul style="font-family: tahoma,arial,helvetica,sans-serif;">
<li><span style="font-size: small;" size="2">Coolsleeves™ 500 for 1/2" OD tubing </span></li>
<li><span style="font-size: small;" size="2">Coolsleeves™ 625 for 5/8" OD tubing </span></li>
</ul>
<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">Each size is available in 4 different colors: clear transparent (non UV reactive), Horizon blue (UV reactive), Saturn Green (UV reactive), and Red (non UV reactive)</span></p>
<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">Coolsleeves™ are shipped in precut 40" length. One length is typically sufficient for a single CPU cooling circuit depending on how tight the coils are wrapped around the tubing. Two lengths are necessary for a complete circuit including dual CPU, CPU+VGA, or CPU+VGA+Chipset setups. </span></p>Swiftech003.0400add-to-cartSwiftechUV Green13mm (1/2")Plastic<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">The advantages of Coolsleeves™ coils are multiple:</span></p>
<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">1. Performance: </span></p>
<ul style="font-family: tahoma,arial,helvetica,sans-serif;">
<li><span style="font-size: small;" size="2">Coolsleeves™ coils do not restrict flow rate compared to internal springs<br /></span></li>
</ul>
<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">2. Reliability: </span></p>
<ul style="font-family: tahoma,arial,helvetica,sans-serif;">
<li><span style="font-size: small;" size="2">Coolsleeves™ coils completely eliminate flattening of the tubes over time </span></li>
<li><span style="font-size: small;" size="2">Coolsleeves™ UV reactive coils are a safe alternative to UV reactive coolant dies and prevent the pump failures caused by these dies. </span></li>
<li><span style="font-size: small;" size="2">Coolsleeves™ coils allow to bend soft vinyl and Tygon tubing at sharp radii without kinking. The sharpest possible radius is achieved by spacing the coils close to each other (3/16"): </span>
<ul>
<li><span style="font-size: small;" size="2">Minimum bending radius for 1/2" Coolsleeves is 1.25" </span></li>
<li><span style="font-size: small;" size="2">Minimum bending radius for 5/8" Coolsleeves is 2.5"</span><span style="font-size: small;" size="2"></span></li>
</ul>
</li>
</ul>
<p style="font-family: tahoma,arial,helvetica,sans-serif; text-align: left;" align="center"><span style="font-size: small;" size="2">A 1.25" bending radius is achieved here with Coolsleeves™ 500</span></p>
<p style="font-family: tahoma,arial,helvetica,sans-serif; text-align: left;" align="center"><span style="font-size: small;" size="2">A 2.5" bending radius is achieved here with Coolsleeves™ 625 and 5/8" Tygon tubing, with a fairly large spacing of 1/4" between coils.</span></p>
<p style="font-family: tahoma,arial,helvetica,sans-serif; text-align: left;" align="center"><span style="font-size: small;" size="2">A 2.5" bending radius is achieved here with Coolsleeves™ 625, and inexpensive 5/8" "thin wall" vinyl tubing, with the coils spaced fairly close to each other (3/16"). Wider coil spacing would not prevent kinking with this type of tubing.</span></p>
<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">4. Convenience:</span></p>
<ul style="font-family: tahoma,arial,helvetica,sans-serif;">
<li><span style="font-size: small;" size="2">Coolsleeves™ can be used with existing 1/2" OD tubing systems to reshape tubes that have flattened over time without disassembling the system. </span></li>
<li><span style="font-size: small;" size="2">Coolsleeves™ 625 now allow users of 1/2" ID tubing to use "thin wall" 5/8" tubes instead of 3/4", for a significant reduction in clutter inside the chassis, and radii that were absolutely impossible to achieve with 3/4" tubing. </span></li>
</ul>
<p style="font-family: tahoma,arial,helvetica,sans-serif;"><span style="font-size: small;" size="2">5. Cosmetics: <br /></span></p>
<ul style="font-family: tahoma,arial,helvetica,sans-serif;">
<li><span style="font-size: small;" size="2">Coolsleeves™ UV reactive coils are fun and attractive under UV light: </span></li>
</ul>
<ul style="font-family: tahoma,arial,helvetica,sans-serif;">
<li><span style="font-size: small;" size="2">..Or in normal light:</span></li>
</ul>
<p style="font-family: tahoma,arial,helvetica,sans-serif;" align="left"><span style="font-size: small;" size="2">6. Cost to consumers:</span></p>
<ul style="font-family: tahoma,arial,helvetica,sans-serif;">
<li><span style="font-size: small;" size="2">Coolsleeves™ 500 coils are more economical than other solutions: the cost per foot including vinyl tubing is up to 50% less than Clearflex™, and up to one third the cost of Tygon™ tubing. </span></li>
</ul>
Good Stock 32 left
Download PDF 
