Hi-flow design: .40" (10.2mm) bore ID x .47" (12mm) barb ID
Recommended use
Initial Tip: If possible, attach the fittings to the cooling devices first! While not mandatory, it is always preferable to fasten a fittings to a cooling device prior to installing the device inside the case. This will eliminate interference issues that may be encountered when working with tools inside of space constrained enclosures.
Fasten the fitting by hand until it mates with the surface of the cooling device. The amount of force necessary to screw the fittings down in “finger tight” mating position may vary from one device to another depending on various factors. Users are advised to always visually check on the actual position of the fitting relative to the device surface rather than solely relying on feel. There should be little -not to exceed the thickness of a sheet of paper, or no visible gap between the fitting lower lip and the device surface. See the illustration below.
For complete long-term safety and leak-free operations, Swiftech® recommends that the fittings be locked in place using the recommended tools and that the torque levels specified below be applied:
Recommended Torque
Soft Material
Minimum
Maximum (*)
Acetal (POM) and acrylics
1/4 of a turn after initial contact between mating surfaces
1/2 of a turn after initial contact between mating surfaces
Hard Materials
Recommended
Copper, brass, aluminum
1/8 of a turn after initial contact between mating surfaces
(*) For full 5mm thread depth – please inspect the device threads prior to applying the maximum recommended torque – when partial threads exist due to application necessity, only apply the minimum torque.
Recommended Tools
A small adjustable wrench with jaw opening up to 1” (25.4mm)
may be used as a universal tool instead of the specific tools listed below
https://www.performance-pcs.com/swiftech-x-lok-seal-compression-fitting-black-3-4x1-2-g1-4-cf-bk.html9878Swiftech ½ x ¾: Lok-Seal Compression Fitting - Blackhttps://www.performance-pcs.com/media/catalog/product/t/m/tmp3-4x1-2-g1-4-cf-bk_01.jpg5.995.9900USDOutOfStock/Water Cooling/Fittings & Connectors0 0Swiftech00https://www.performance-pcs.com/media/catalog/product/t/m/tmp3-4x1-2-g1-4-cf-bk_02.jpg3.8800add-to-cartlow-stockSwiftechNoCompression1/2" x 3/4"Straight<table border="0">
<tbody>
<tr>
<td>
<table style="width: 600px; border-collapse: collapse;" align="left">
<tbody>
<tr>
<td style="text-align: center; width: 300px; background: #dcdcdc;">
<p align="left"><span style="color: #000000;"><strong>Contents & Features</strong></span></p>
</td>
<td style="text-align: center; width: 300px; background: #dcdcdc;">
<p align="left"><span style="color: #000000;"><strong>Specifications</strong></span></p>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>
<div align="left">Blister pack of 1 fitting & collar</div>
</li>
</ul>
</td>
<td>
<ul>
<li>
<div align="left">Material: brass</div>
</li>
</ul>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>
<div align="left">For ½” (13mm) ID x ¾” (19mm) OD tubing</div>
</li>
</ul>
</td>
<td>
<ul>
<li>
<div align="left">Finish: high polish chrome plating or black paint</div>
</li>
</ul>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>
<div align="left">G 1/4" Male threads</div>
</li>
</ul>
</td>
<td>
<ul>
<li>
<div align="left">Hex nut: Inch 15/16" - Metric 24mm</div>
</li>
<li>
<div align="left">Collar: Inch 1" - Metric 25mm</div>
</li>
</ul>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>
<div align="left">Hi-flow design: .40" (10.2mm) bore ID x .47" (12mm) barb ID</div>
</li>
</ul>
</td>
<td>
<p align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/anatomy.jpg" border="0" /></p>
</td>
</tr>
</tbody>
</table>
</td>
</tr>
</tbody>
</table>
<table style="width: 644px; height: 1344px;" border="0">
<tbody>
<tr>
<td>
<p><strong>Recommended use<br /></strong></p>
<ul>
<li>
<div>Initial Tip: If possible, attach the fittings to the cooling devices first! While not mandatory, it is always preferable to fasten a fittings to a cooling device prior to installing the device inside the case. This will eliminate interference issues that may be encountered when working with tools inside of space constrained enclosures.</div>
</li>
<li>
<div>Fasten the fitting by hand until it mates with the surface of the cooling device. The amount of force necessary to screw the fittings down in “finger tight” mating position may vary from one device to another depending on various factors. Users are advised to always visually check on the actual position of the fitting relative to the device surface rather than solely relying on feel. There should be little -not to exceed the thickness of a sheet of paper, or no visible gap between the fitting lower lip and the device surface. See the illustration below.</div>
</li>
</ul>
<p> </p>
<p align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/gonogo.jpg" border="0" /></p>
<ul>
<li>
<div>For complete long-term safety and leak-free operations, Swiftech® recommends that the fittings be locked in place using the recommended tools and that the torque levels specified below be applied:</div>
</li>
</ul>
<table style="width: 600px; border-collapse: collapse; border: black 1px solid;" align="center">
<tbody>
<tr>
<td style="background: #000000; color: #ffffff; border: black 1px solid;" colspan="3">
<p align="center">Recommended Torque</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;"><span style="color: #000000;">Soft Material</span></td>
<td style="background: #dcdcdc; border: black 1px solid;">
<p align="center"><span style="color: #000000;">Minimum</span></p>
</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<p align="center"><span style="color: #000000;">Maximum (*)</span></p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">Acetal (POM) and acrylics</td>
<td style="border: black 1px solid;">
<p align="center">1/4 of a turn after initial contact between mating surfaces</p>
</td>
<td style="border: black 1px solid;">
<p align="center">1/2 of a turn after initial contact between mating surfaces</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;"><span style="color: #000000;">Hard Materials</span></td>
<td style="background: #dcdcdc; border: black 1px solid;" colspan="2">
<p align="center"><span style="color: #000000;">Recommended</span></p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">Copper, brass, aluminum</td>
<td style="border: black 1px solid;" colspan="2">
<p align="center">1/8 of a turn after initial contact between mating surfaces</p>
</td>
</tr>
</tbody>
</table>
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<div align="left">(*) For full 5mm thread depth – please inspect the device threads prior to applying the maximum <br />recommended torque – when partial threads exist due to application necessity, only apply the <br />minimum torque.</div>
<div align="left"> </div>
</blockquote>
</blockquote>
</blockquote>
</blockquote>
</blockquote>
<p dir="ltr" align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/torque-range.jpg" border="0" /></p>
<table style="width: 600px; border-collapse: collapse; border: black 1px solid;">
<tbody>
<tr>
<td style="background: #000000; color: #ffffff; border: black 1px solid;" colspan="3">
<p align="center">Recommended Tools</p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;" colspan="3">
<div align="center"><em>A small adjustable wrench with jaw opening up to 1” (25.4mm) </em></div>
<div align="center"><em>may be used as a universal tool </em><em>instead of the specific tools listed below</em></div>
</td>
</tr>
<tr>
<td style="background: #000000; color: #ffffff; border: black 1px solid;" colspan="3">
<p align="center">Specific tool sizes</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;">
<div align="center"><span style="color: #000000;">Fitting</span></div>
<div align="center"><span style="color: #000000;"> </span></div>
<div><span style="color: #000000;">Inch Tube ID x OD</span></div>
<div><span style="color: #000000;">Metric Tube OD xID</span></div>
</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<div align="center"><span style="color: #000000;">Fitting base hex:</span></div>
<div align="center"><span style="color: #000000;"> </span></div>
<div align="center"><span style="color: #000000;">Flat wrench or socket</span></div>
</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<div align="center"><span style="color: #000000;">Collar:</span></div>
<div align="center"><span style="color: #000000;"> </span></div>
<div align="center"><span style="color: #000000;">Flat or adjustable wrench</span></div>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">⅜”x ½” – 13/10mm</td>
<td style="border: black 1px solid;">Metric: 17mm - Inch: 11/16”</td>
<td style="border: black 1px solid;">Metric: 18mm - Inch: adjustable wrench</td>
</tr>
<tr>
<td style="border: black 1px solid;">⅜” x ⅝” – 16/10mm</td>
<td style="border: black 1px solid;">Metric: 20mm - Inch: 13/16”</td>
<td style="border: black 1px solid;">Metric: 21mm - Inch: adjustable wrench</td>
</tr>
<tr>
<td style="background: #ffd700; border: black 1px solid;"><span style="color: #000000;">½” x ¾” – 19/13mm</span></td>
<td style="background: #ffd700; border: black 1px solid;"><span style="color: #000000;">Metric: 24mm - Inch: 15/16”</span></td>
<td style="background: #ffd700; border: black 1px solid;"><span style="color: #000000;">Metric: 25mm - Inch: 1”</span></td>
</tr>
</tbody>
</table>
</td>
</tr>
</tbody>
</table>0