45° Swivel Elbow Lok-Seal™ adapter: the base freely rotates 360° and the female thread allows installation of a compression fitting to make a 45° Swivel elbow fitting.
45° Swivel Elbow Lok-Seal™ adapter: the base freely rotates 360° and the female thread allows installation of a compression fitting to make a 45° Swivel elbow fitting.
Initial Tip: If possible, attach the fittings to the cooling devices first! While not mandatory, it is always preferable to fasten a fittings to a cooling device prior to installing the device inside the case. This will eliminate interference issues that may be encountered when working with tools inside of space constrained enclosures.
Fasten the fitting by hand until it mates with the surface of the cooling device. The amount of force necessary to screw the fittings down in “finger tight” mating position may vary from one device to another depending on various factors. Users are advised to always visually check on the actual position of the fitting relative to the device surface rather than solely relying on feel. There should be little -not to exceed the thickness of a sheet of paper, or no visible gap between the fitting lower lip and the device surface. See the illustration below.
For complete long-term safety and leak-free operations, Swiftech® recommends that the fittings be locked in place using the recommended tools and that the torque levels specified below be applied:
Recommended Torque
Soft Material
Minimum
Maximum (*)
Acetal (POM) and acrylics
1/4 of a turn after initial contact between mating surfaces
1/2 of a turn after initial contact between mating surfaces
Hard Materials
Recommended
Copper, brass, aluminum
1/8 of a turn after initial contact between mating surfaces
(*) For full 5mm thread depth – please inspect the device threads prior to applying the maximum recommended torque – when partial threads exist due to application necessity, only apply the minimum torque.
Recommended Tools
A small adjustable wrench with jaw opening up to 1” (25.4mm)
may be used as a universal tool instead of the specific tools listed below
https://www.performance-pcs.com/swiftech-45-swivel-elbow-lok-seal-adapter-black-45d-swv-g1-4-mfa-bk.html10063Swiftech 45° Swivel Elbow Lok-Seal Adapter - Blackhttps://www.performance-pcs.com/media/catalog/product/t/m/tmp45d-swv-g1-4-mfa-bk_01.jpg8.498.4900USDOutOfStock/Water Cooling/Fittings & Connectors<p>45° Swivel Elbow Lok-Seal™ adapter: the base freely rotates 360° and the female thread allows installation of a compression fitting to make a 45° Swivel elbow fitting.</p> <p>45° Swivel Elbow Lok-Seal™ adapter: the base freely rotates 360° and the female thread allows installation of a compression fitting to make a 45° Swivel elbow fitting.</p>Swiftech005.5000add-to-cartlow-stockSwiftechAdapter45 Degree<table>
<tbody>
<tr>
<td>
<table style="width: 600px; border-collapse: collapse;" align="left">
<tbody>
<tr>
<td style="text-align: center; width: 300px; background: #dcdcdc;"><span style="color: #000000;"><strong>Contents & Features</strong></span></td>
<td style="text-align: center; width: 300px; background: #dcdcdc;"><span style="color: #000000;"><strong>Specifications</strong></span></td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>Blister pack of 1 fitting & collar</li>
</ul>
</td>
<td>
<ul>
<li>Material: brass</li>
</ul>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>
<div>G¼" Male and Female threads</div>
</li>
</ul>
</td>
<td>
<ul>
<li>Finish: high polish chrome plating or black paint</li>
</ul>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>360° swivel with hi-flow 10.2mm bore</li>
</ul>
</td>
<td>
<ul>
<li>
<div>Hex nut:</div>
<ul>
<li>
<div>Inch: .67"</div>
</li>
<li>
<div>Metric: 17mm</div>
</li>
</ul>
</li>
</ul>
</td>
</tr>
</tbody>
</table>
</td>
</tr>
</tbody>
</table>
<p> </p>
<table style="width: 51%;">
<tbody>
<tr>
<td style="width: 676px;">
<p><strong>Recommended use<br /></strong></p>
<ul>
<li>
<div>Initial Tip: If possible, attach the fittings to the cooling devices first! While not mandatory, it is always preferable to fasten a fittings to a cooling device prior to installing the device inside the case. This will eliminate interference issues that may be encountered when working with tools inside of space constrained enclosures.</div>
</li>
<li>
<div>Fasten the fitting by hand until it mates with the surface of the cooling device. The amount of force necessary to screw the fittings down in “finger tight” mating position may vary from one device to another depending on various factors. Users are advised to always visually check on the actual position of the fitting relative to the device surface rather than solely relying on feel. There should be little -not to exceed the thickness of a sheet of paper, or no visible gap between the fitting lower lip and the device surface. See the illustration below.</div>
</li>
</ul>
<p> </p>
<p align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/gonogo.jpg" border="0" height="222" width="600" /></p>
<ul>
<li>
<div>For complete long-term safety and leak-free operations, Swiftech® recommends that the fittings be locked in place using the recommended tools and that the torque levels specified below be applied:</div>
</li>
</ul>
<table style="width: 600px; border-collapse: collapse; border: black 1px solid;" align="center">
<tbody>
<tr>
<td colspan="3" style="background: #000000; color: #ffffff; border: black 1px solid;">
<p align="center">Recommended Torque</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;"><span style="color: #000000;">Soft Material</span></td>
<td style="background: #dcdcdc; border: black 1px solid;">
<p align="center"><span style="color: #000000;">Minimum</span></p>
</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<p align="center"><span style="color: #000000;">Maximum (*)</span></p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">Acetal (POM) and acrylics</td>
<td style="border: black 1px solid;">
<p align="center">1/4 of a turn after initial contact between mating surfaces</p>
</td>
<td style="border: black 1px solid;">
<p align="center">1/2 of a turn after initial contact between mating surfaces</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;"><span style="color: #000000;">Hard Materials</span></td>
<td colspan="2" style="background: #dcdcdc; border: black 1px solid;">
<p align="center"><span style="color: #000000;">Recommended</span></p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">Copper, brass, aluminum</td>
<td colspan="2" style="border: black 1px solid;">
<p align="center">1/8 of a turn after initial contact between mating surfaces</p>
</td>
</tr>
</tbody>
</table>
<blockquote dir="ltr" style="margin-right: 0px;">
<blockquote dir="ltr" style="margin-right: 0px;">
<blockquote dir="ltr" style="margin-right: 0px;">
<blockquote dir="ltr" style="margin-right: 0px;">
<blockquote dir="ltr" style="margin-right: 0px;">
<div align="left">(*) For full 5mm thread depth – please inspect the device threads prior to applying the maximum <br />recommended torque – when partial threads exist due to application necessity, only apply the <br />minimum torque.</div>
<div align="left"> </div>
</blockquote>
</blockquote>
</blockquote>
</blockquote>
</blockquote>
<div dir="ltr" align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/torque-range.jpg" border="0" /></div>
<div dir="ltr" align="center">
<table style="width: 600px; border-collapse: collapse; border: black 1px solid;">
<tbody>
<tr>
<td colspan="9" style="background: #000000; color: #ffffff; border: black 1px solid;">
<p align="center">Recommended Tools</p>
</td>
</tr>
<tr>
<td colspan="9" style="background: #ffffff; color: #ffffff; border: black 1px solid;">
<div align="center"></div>
<div align="center"><em><span style="color: #000000;">A small adjustable wrench with jaw opening up to 1” (25.4mm) </span></em></div>
<div align="center"><span style="color: #000000;"><em>may be used as a universal tool instead of the specific tools listed below</em></span></div>
<div align="center"></div>
</td>
</tr>
<tr>
<td colspan="9" style="background: #000000; color: #ffffff; border: black 1px solid;">
<p align="center">Specific tool sizes</p>
</td>
</tr>
<tr>
<td colspan="8" style="width: 250px; background: #dcdcdc; color: #ffffff; border: black 1px solid;">
<p align="center"><span style="background-color: #dcdcdc; color: #000000;"> Adapter</span></p>
</td>
<td style="background: #dcdcdc; color: #000000; border: black 1px solid;">
<div align="center">Fitting Base Hex:</div>
<div style="color: #000000;" align="center">Flat wrench</div>
</td>
</tr>
<tr>
<td colspan="8" style="background: #ffffff; color: #ffffff; border: black 1px solid;">
<p align="center"><span style="color: #000000;">90° Swivel Elbow</span></p>
</td>
<td style="background: #ffffff; color: #ffffff; border: black 1px solid;">
<p align="center"><span style="color: #000000;">Inch: 5/8" - Metric: 17mm</span></p>
</td>
</tr>
<tr>
<td colspan="8" style="background: #ffffff; color: #ffffff; border: black 1px solid;">
<p align="center"><span style="color: #000000;">90° Dual Swivel Elbow</span></p>
</td>
<td style="background: #ffffff; color: #000000; border: black 1px solid;">
<p align="center">In<span style="color: #000000;">ch: 5/8" - Metric: 17mm</span></p>
</td>
</tr>
<tr>
<td colspan="8" style="background: #ffd700; color: #000000; border: black 1px solid;">
<p align="center"><span style="color: #000000;">45° Swivel Elbow</span></p>
</td>
<td style="background: #ffd700; color: #000000; border: black 1px solid;">
<p align="center"><span style="color: #000000;">Inch: 5/8" - Metric: 17mm</span></p>
</td>
</tr>
</tbody>
</table>
</div>
</td>
</tr>
</tbody>
</table><div><strong>Dimensions</strong></div>
<div align="center"> </div>
<div align="center"><img style="float: left;" alt="" src="http://www.swiftech.org/images/products/Lok-seal/45d-Swivel-Elbow.jpg" border="0" height="560" width="400" /></div>