G¼ Male-Male adjustable connector fittings for multiple VGA waterblocks in SLI or CrossfireX. This product is part of the Lok-Seal family of fittings.
Recommended use
Initial Tip: If possible, attach the fittings to the cooling devices first! While not mandatory, it is always preferable to fasten a fitting to a cooling device prior to installing the device inside the case. This will eliminate interference issues that may be encountered when working with tools inside of space constrained enclosures.
Fasten the fitting by hand until it mates with the surface of the cooling device. The amount of force necessary to screw the fittings down in “finger tight” mating position may vary from one device to another depending on various factors. Users are advised to always visually check on the actual position of the fitting relative to the device surface rather than solely relying on feel. There should be little -not to exceed the thickness of a sheet of paper, or no visible gap between the fitting lower lip and the device surface. See the illustration below.
For complete long-term safety and leak-free operations, Swiftech® recommends that the fittings be locked in place using the recommended tools and that the torque levels specified below be applied:
Recommended Torque
Soft Material
Minimum
Maximum (*)
Acetal (POM) and acrylics
1/4 of a turn after initial contact between mating surfaces
1/2 of a turn after initial contact between mating surfaces
Hard Materials
Recommended
Copper, brass, aluminum
1/8 of a turn after initial contact between mating surfaces
(*) For full 5mm thread depth – please inspect the device threads prior to applying the maximum recommended torque – when partial threads exist due to application necessity, only apply the minimum torque.
Recommended Tools
A small adjustable wrench with jaw opening up to 1” (25.4mm)
may be used as a universal tool instead of the specific tools listed below
https://www.performance-pcs.com/swiftech-g-male-male-lok-seal-medium-extension-fitting-20-33mm-range-black-g1-4-mmext-medium-bk.html9830Swiftech G¼ Male-Male Lok-Seal Medium Extension Fitting (20-33mm Range) - Blackhttps://www.performance-pcs.com/media/catalog/product/t/m/tmpg1-4-mmext-medium-bk_01.jpg7.957.9500USDOutOfStock/Water Cooling/Water Block Accessories/Accessories-GPU Blocks0 <p><span style="font-family: tahoma,arial,helvetica,sans-serif; font-size: small;" size="2">G<span style="line-height: 115%; font-size: 10pt;">¼</span> Male-Male adjustable connector fittings for multiple VGA waterblocks in SLI or CrossfireX. This product is part of the Lok-Seal family of fittings. </span></p>
<p><span style="font-family: tahoma,arial,helvetica,sans-serif; font-size: small;" size="2"></span></p>
<p><strong>Recommended use<br /></strong></p>
<p><span style="font-family: tahoma,arial,helvetica,sans-serif; font-size: small;" size="2"></span></p>
<ul>
<li>
<div>Initial Tip: If possible, attach the fittings to the cooling devices first! While not mandatory, it is always preferable to fasten a fitting to a cooling device prior to installing the device inside the case. This will eliminate interference issues that may be encountered when working with tools inside of space constrained enclosures.</div>
</li>
<li>
<div>Fasten the fitting by hand until it mates with the surface of the cooling device. The amount of force necessary to screw the fittings down in “finger tight” mating position may vary from one device to another depending on various factors. Users are advised to always visually check on the actual position of the fitting relative to the device surface rather than solely relying on feel. There should be little -not to exceed the thickness of a sheet of paper, or no visible gap between the fitting lower lip and the device surface. See the illustration below.</div>
</li>
</ul>
<p><span style="font-family: tahoma,arial,helvetica,sans-serif; font-size: small;" size="2"><br /></span></p>Swiftech004.8800add-to-cartlow-stockSwiftechUniversalNvidia/AMDSLI Fitting<table style="width: 600px; border-collapse: collapse;" align="center">
<tbody>
<tr>
<td style="width: 300px; background: none repeat scroll 0% 0% #dcdcdc; text-align: center;"><strong>Contents & Features</strong></td>
<td style="width: 300px; background: none repeat scroll 0% 0% #dcdcdc; text-align: center;"><strong>Specifications</strong></td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li><strong>Blister Pack of ONE (1) fitting</strong></li>
</ul>
</td>
<td>
<ul>
<li>Material: brass</li>
</ul>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>
<div>Adjustable length range: <br />Metric: 20-33mm Inch: .79-1.3"</div>
</li>
</ul>
</td>
<td>
<ul>
<li>Finish: high polish chrome plating or black paint</li>
</ul>
</td>
</tr>
<tr>
<td style="width: 300px;">
<ul>
<li>
<div><span>Locking nut feature:</span></div>
<div> </div>
<div style="text-align: left;">Locks male & female in place once spacing adjustement has been set.</div>
</li>
</ul>
</td>
<td>
<ul>
<li>Hex nut: compatible with 5/8" or 16mm flat wrench</li>
</ul>
</td>
</tr>
</tbody>
</table>
<div style="text-align: center;"> </div>
<table style="border-collapse: collapse; margin-left: 5px; margin-right: 5px;" cellpadding="5" align="center">
<tbody>
<tr>
<td style="width: 305px; background: #dcdcdc;">
<p align="center"><strong>Applications examples</strong></p>
</td>
</tr>
<tr>
<td style="width: 305px; background: #ffffff;">
<div><img alt="" src="http://www.swiftech.org/images/products/KOMOD HD7970/xfire2,3.jpg" border="0" /></div>
<div>60mm/2.3" PCI spacing: Komodo HD7900 series waterblocks in CrossFireX with stock bridge</div>
<div><hr /></div>
<div><img alt="" src="http://www.swiftech.org/images/products/display/Komod6970Xfire1,6.jpg" border="0" /></div>
<div>40mm/1.6" PCI spacing: Komodo HD6900 series waterblocks in CrossFireX</div>
</td>
</tr>
</tbody>
</table><div><strong>Dimensions</strong></div>
<div> </div>
<p align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/G1-4-MMEXT-MEDIUMx400.jpg" border="0" /></p>
<div> </div>
<p> </p>
<p align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/gonogo.jpg" border="0" /></p>
<ul>
<li>
<div>For complete long-term safety and leak-free operations, Swiftech® recommends that the fittings be locked in place using the recommended tools and that the torque levels specified below be applied:</div>
</li>
</ul>
<table style="width: 600px; border-collapse: collapse; border: black 1px solid;" align="center">
<tbody>
<tr>
<td style="background: #000000; color: #ffffff; border: black 1px solid;" colspan="3">
<p align="center">Recommended Torque</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;">Soft Material</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<p align="center">Minimum</p>
</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<p align="center">Maximum (*)</p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">Acetal (POM) and acrylics</td>
<td style="border: black 1px solid;">
<p align="center">1/4 of a turn after initial contact between mating surfaces</p>
</td>
<td style="border: black 1px solid;">
<p align="center">1/2 of a turn after initial contact between mating surfaces</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;">Hard Materials</td>
<td style="background: #dcdcdc; border: black 1px solid;" colspan="2">
<p align="center">Recommended</p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">Copper, brass, aluminum</td>
<td style="border: black 1px solid;" colspan="2">
<p align="center">1/8 of a turn after initial contact between mating surfaces</p>
</td>
</tr>
</tbody>
</table>
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<blockquote style="margin-right: 0px;" dir="ltr">
<div align="left">(*) For full 5mm thread depth – please inspect the device threads prior to applying the maximum <br />recommended torque – when partial threads exist due to application necessity, only apply the <br />minimum torque.</div>
<div align="left"> </div>
</blockquote>
</blockquote>
</blockquote>
</blockquote>
</blockquote>
<div dir="ltr" align="center"><img alt="" src="http://www.swiftech.org/images/products/Lok-seal/torque-range.jpg" border="0" /></div>
<div dir="ltr" align="center"> </div>
<div dir="ltr" align="center"> </div>
<div dir="ltr" align="center">
<table style="width: 600px; border-collapse: collapse; border: black 1px solid;">
<tbody>
<tr>
<td style="background: #000000; color: #ffffff; border: black 1px solid;" colspan="3">
<p align="center">Recommended Tools</p>
</td>
</tr>
<tr>
<td style="border: black 1px solid;" colspan="3">
<div align="center"><em>A small adjustable wrench with jaw opening up to 1” (25.4mm) </em></div>
<div align="center"><em>may be used as a universal tool </em><em>instead of the specific tools listed below</em></div>
</td>
</tr>
<tr>
<td style="background: #000000; color: #ffffff; border: black 1px solid;" colspan="3">
<p align="center">Specific tool sizes</p>
</td>
</tr>
<tr>
<td style="background: #dcdcdc; border: black 1px solid;">
<div align="center">Male/male</div>
<div align="center">Connectors</div>
</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<div align="center">Fitting base hex:</div>
<div align="center"> </div>
<div align="center">Flat wrench</div>
</td>
<td style="background: #dcdcdc; border: black 1px solid;">
<div align="center">Lock Nut</div>
<div align="center"> </div>
<div align="center">Flat or adjustable wrench</div>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">G1/4 MMEXT Short (11-18mm)</td>
<td style="border: black 1px solid;">
<div>Metric: 16mm</div>
<div>Inch: 5/8”</div>
</td>
<td style="border: black 1px solid;">N/A</td>
</tr>
<tr>
<td style="background: #ffd700; border: black 1px solid;">G1/4 MMEXT Medium (20-33mm)</td>
<td style="background: #ffd700; border: black 1px solid;">
<div>Metric: 16mm</div>
<div>Inch: 5/8”</div>
</td>
<td style="background: #ffd700; border: black 1px solid;">
<div>Metric: 17mm</div>
<div>Inch: adjustable wrench</div>
</td>
</tr>
<tr>
<td style="border: black 1px solid;">G1/4 MMEXT Long (41-65mm)</td>
<td style="border: black 1px solid;">
<div>Metric: 16mm</div>
<div>Inch: 5/8”</div>
</td>
<td style="border: black 1px solid;">
<div>Metric: 17mm</div>
<div>Inch: adjustable wrench</div>
</td>
</tr>
</tbody>
</table>
</div>