Phobya CPU-Cooler UC-2 LT Intel 775,1155,1156,1366,2011 - Black Edition
The core of the Phobya UC-2 is a novel intermediate level, based on the patented in 2008, Mirko return channel technology that was already in the previous model used was developed. Challenge, it was this technology that was developed for a pin structure to optimize a slot structure of the ground plate.
This cooler rightly deserves its name: "Phobya Ultra Cooling, the first" or in short: UC-1
The core of the Phobya UC-1 is a novel intermediate level, based on the patented in 2008, Mirko return channel technology that was already in the previous model used was developed. Challenge, it was this technology that was developed for a pin structure to optimize a slot structure of the ground plate. The result is a CPU cooler, which is one of the best on the market, not only in terms of excellent cooling performance, but also the manufacture and design are of high quality and innovative. The cooler is to launch immediately become the new number 1 of the CPU water cooler. [Accessed 06/14/2012 Source: Hardwaremax]
The underside of the cooler is polished and provided with a protective film, which are removed prior to assembly must. The cooler features a large 56x56mm base plate with a razor-thin slit structure, which is one of the most advanced on the market. Covering an area of approximately 35 x 31.3 mm, 68 cooling channels attached which only about 0.2 mm wide. The intermediate cooling fins have a width of only about 0.2 mm too. About these slots have a 1mm thick intermediate layer is set that satisfies two functions:
First In the middle there is a centric injection slot that the water which is collected behind the inlet in a pre-chamber, perpendicular to the slot structure injects into the cooling channels.
Second On the underside of the intermediate level are water return channels, which are so arranged that the flow is increased which results in cross-flows in addition micro turbulence in and above the cooling fins which increase the cooling performance.
The injection slit (width, length, number) and the arrangement of the feedback channels were tested through extensive testing in all possible variations to the optimal result was present. Rounding out the radiator with a skillful discharge of cooling water, passing it from the rear reservoir via two back-flow channels to the outlet. Inlet and outlet are fabulous 23mm (measured from the center) apart, so that hoses can easily be used with 16mm outside diameter. As a result, the UC-1 thus obtained Phobya both single, dual, or quad / hexa core cooling sensational performances.
The well-known predecessor of the black piano lacquer design was further refined and visually rounded. In addition to the glossy black-caps are now the bracket and the screws completely in black. The surface is described by a Lasergravour, so that the inlet and outlet with arrows labeled. The cooler is available in two versions, one for AMD and one for Intel motherboards.
The "Extreme" version unfolds the full potential of the micro-channel feedback technology combined with a solid metal lid of a higher quality and additional performance improvement possible. This cooler provides maximum performance and is especially suitable for extreme overclocking. Who wants to get the most out of his PC, with this cooler very well advised. The "LT" version allows an affordable beginning, the performance values are compared with the "Extreme" is less by only 2 to 3 K (tested on i2970K Core (Quad Core)). Who wants to TOP cooling performance at a fair price for the LT version is exactly right.
- Water cooler material: copper, plastic
- Bracket material: aluminum
- Intel version Dimensions: 94 x 94 x 15mm
- Weight: 215 grams
- Connection thread: G1 / 4 "
- Mounting screws Size: M4
- Compatibility: Intel: 775, 1366, 1156, 1155, 2011, Xeon
The installation instructions can be found here.
- 1x CPU Cooler Phobya UC-1 LT Intel 775,1155,156,1366,2011 - Black Edition
- 1x Thermal Phobya HeGrease Extreme
- 1x Mounting materials
The cooler is shipped pre-assembled and pressure tested. In case of disassembly will void the warranty on the radiator for leaks.